Pumps for Lift

Lift pumps are specialised devices designed to efficiently move liquids or gases from a lower level to a higher one. They are widely used in a variety of industries, including industry, agriculture, construction, water supply and others. These pumps provide a reliable and efficient way to transport liquids and gases to different heights, which allows you to optimise production processes, increase efficiency and reduce operating costs.

TOP-20 Pumps for lift + other products

VKC Sealless Mag-Drive Vertical Pumps

VKC Sealless Mag-Drive Vertical Pumps

The vertical centrifugal pump is designed to submerge the pump in the pumped liquid so that the electric motor remains above the liquid level. The semi-submersible chemical pump uses special construction materials and technical solutions that allow it to withstand chemical attack not only from the inside but also from the outside. We offer sealed semi-submersible vertical pumps with magnetic coupling and pumps with mechanical seal for pumping sodium hydroxide and hypochlorite, sulfuric, hydrochloric, nitric acid, alkalis, various corrosive mixtures, solvent, wastewater with chemical impurities, etc.

Flow Range: to 15.7 m 3 /h
Temperature: 60° C
Pressure: 4.1 bar
Length: to 152 cm
Industrial Progressive Cavity Pump

Industrial Progressive Cavity Pump

The pumps are used in various enterprises, industries, in the most difficult operating conditions, ensuring smooth fluid transfer. The pumps are suitable for pumping liquids with low and high viscosity, as well as for pumping abrasive, sticky, crushing and foaming liquids. The pumps are particularly suited for handling products with solid particles. The suction capacity is max. 5m/s. The pumps deliver regular, linear, pulsation-free and measured flow. Quiet operation without vibration.

Flow Range: max. 500 m3/h
Viscosity: up to 3,000,000 St
Temperature: max. +150 °C
Pressure: max. 48 bar
Solids: presence of particles up to 7%
Materials: cast iron, cast steel, stainless steel
Hopper pumps

Hopper pumps

The design of the pumps allows them to be used for many different applications. The standard design includes an enlarged rectangular inlet hopper with a screw conveyor that pushes the product to be pumped into the pump's working section. There are versions in which the pump inlet is equipped with a large screw, an integrated cork breaker or both. Most pumps are supplied in a monoblock design (direct connection of the pump to the electric motor) or with a free shaft outlet (without an electric motor).

Flow Range: up to 200 m3/h
Viscosity: up to 3.000.000 cSt
Pressure: up to 36 bar
Solids: presence of particles up to 40%
Materials: steel, cast stainless steel
Flexible impeller pumps

Flexible impeller pumps

The MENC-INOX industrial pumps are pumps with a flexible stainless steel impeller. The impeller deforms inside the stainless steel casing to provide fast suction of up to 5 m and constant and accurate liquid transfer. In addition, the low speed makes this pump suitable for pumping liquids and media containing solids that require careful handling. Due to the low speed, pumping is carried out without harmful foaming of the emulsion, the so-called "shear effect".

Flow Range: up to 930 lt/min
Temperature: max 70°C
Pressure: max 3 bar
Materials: stainless steel
Head: up to 35 mt
Hygienic Series

Hygienic Series

Pneumatic diaphragm pumps of the hygienic series are made of polished stainless steel AISI 316L. The pumps are hermetically sealed, self-priming, and are designed primarily for pumping of slightly aggressive media, food and cosmetic products. They are used in those industries where there are increased requirements to hygiene, for example dairy production.

Flow Range: max. 850 l/min
Temperature: up to 120°C
Pressure: 8 bar
Solids: max. 15 mm
Materials: AISI 316 L
Hygienic Series

Hygienic Series

Pneumatic diaphragm pumps of the hygienic series are made of polished stainless steel AISI 316L. The pumps are hermetically sealed, self-priming, and are designed primarily for pumping of slightly aggressive media, food and cosmetic products. They are used in those industries where there are increased requirements to hygiene, for example dairy production.

Flow Range: max. 850 l/min
Temperature: up to 120°C
Pressure: 8 bar
Solids: max. 15 mm
Materials: AISI 316 L
Valisi metallic series V

Valisi metallic series V

Valisi metal pumps of the V series are available in a variety of construction materials: aluminium and stainless steel. This series of pumps for industrial applications provides high efficiency and reliability for continuous operation. With a flow rate of up to 908 l/min and a wide variety of materials and channel configurations, you will find the right pump for your application. FDA-compliant metal pumps are available, specially manufactured from materials that are safe for food, beverage, pharmaceutical and cosmetic processes where 3A, USDA or EHEDG standards are not required. The simple, robust design features trouble-free air valve operation, oil-free operation, reliable on/off operation, easy operation and maintenance, and delicate/shear-sensitive product handling. The pumps comply with EU Directive 1935/2004.

Flow Range: up to 908 l/min
Temperature: Determined by elastomers
Pressure: up to 8 bar
Solids: up to 12.7 mm
Materials: aluminium, 316 stainless steel, cast iron
Dimensions: up to 3 in.
Valisi metallic series VC

Valisi metallic series VC

The modern metal  diaphragm pump of VC series features a unique, non-jamming air valve that is simple, robust and reliable, and does not require a separate or mechanically operated pilot valve. The bolted design ensures leak-free pumping of liquids. The pneumatic diaphragm pumps are designed and manufactured to meet the needs of both OEMs and end users. The main characteristics of these pumps are competitive prices, few parts, simple design and maintenance, and high quality. Stainless steel pumps are FDA approved. Aluminium pumps with PTFE diaphragms are explosion-proof and ATEX certified.

Flow Range: up to 903 l/min
Temperature: depends on elastomer
Pressure: up to 8 bar
Solids: up to 9 mm
Materials: aluminium, cast iron, carbon steel, SS 316
Dimensions: up to 3 in.
Horizontal centrifugal pumps

Horizontal centrifugal pumps

Idrochemical NCM centrifugal pumps comply with the dimensional criteria of ISO 2858 and ISO 5199. The casing and impeller profiles are designed to achieve high hydraulic efficiency and low NPSH.

The NCM line is available in five bearing housing sizes with wide interchangeability of parts, which allows for low maintenance spares.

Flow Range: up to 1500 m3/h
Temperature: -80°C to 350°C
Pressure: to 25 bar
Dimensions: Discharge size from 20 mm (¾ in) to 300 mm (12 in)
Head: up to 140 m
Closed coupled centrifugal pumps

Closed coupled centrifugal pumps

With pump ends conforming to ISO 2858 dimensional and technical standards and to ISO 5199 design criteria, the NCB provides a compact, space-saving arrangement ideal for industrial processes or installations when space is at a premium. NCB pumps are fitted with standard, readily available electric motors so the user can choose an enclosure to suit the application.

Heavy-Duty Casing with integral foot and multi-ribbed discharge flange provides superior resistance to pipe loads.

Flow Range: up to 300 m3/h
Temperature: -80°C to 350°C
Pressure: to 25 bar
Dimensions: Discharge size from 20 mm (¾ in) to 300 mm (12 in)
Head: up to 140 m
Vertical centrifugal pumps

Vertical centrifugal pumps

You can buy centrifugal vertical single-stage pumps of the NCV series from ASCO PUMPS Uzbekistan. The maximum shaft length is 5 m. The standard design is designed for rotational speeds up to 2900 rpm. The radial bearings are lubricated by the pumped liquid, provided it does not contain any suspended abrasive particles. If the pumped fluid is slightly abrasive, the radial bearings are lubricated with an external special transparent grease.

Flow Range: to 2500 m3/h
Temperature: -80°C to +350°C
Pressure: to 16 bar
Materials: cast iron, steel, carbon steel, stainless steel, nickel, Hastelloy, titanium, bronze
Dimensions: Discharge size from 20 mm to 300 mm
Length: up to 1500 mm
Centrifugal axial flow pump entirely made of SS

Centrifugal axial flow pump entirely made of SS

The EL series pumps are designed for pumping liquids containing solid particles. The axial impeller is resistant to wear in contaminated media.

Flow Range: up to 720 lt/min
Temperature: max 110°C
Pressure: max 3 bar
Materials: AISI 304/316 high thickness stainless steel
Dimensions: G 1, G 1 ½, G 1 ¼
Head: up to 23 mt
Sanitary centrifugal stainless steel pump LT series

Sanitary centrifugal stainless steel pump LT series

The new LT series of electric sanitary pumps has been created using advanced cold pressing technology that allows the pumps to operate in difficult conditions. The LT series pumps are designed and manufactured to ensure the highest hygiene and prevent any contamination of the liquid.
Flow Range: up to 930 lt/min
Temperature: max 80°C
Pressure: max 6 bar
Materials: AISI 316 high thickness stainless steel
Head: up to 35 mt
CM monobloc pump series

CM monobloc pump series

CMA series pumps are open impeller pumps designed for pumping liquids with suspended solids and solid particles. CMC series pumps are pumps with a closed impeller made of two stainless steel disks. CMA/CMC series pumps are used for transportation of large volumes of chemically active liquids and acids, for petroleum products, in galvanizing, pharmaceutical and paint and varnish industries.

Flow Range: up to 1800 lt/min
Temperature: max 110°C
Pressure: max 10 bar
Materials: AISI 304/316 high thickness stainless steel
Head: up to 60 mt
SP Series Self-Priming Pumps

SP Series Self-Priming Pumps

The SP series plastic centrifugal sealed chemical pumps with magnetic coupling are ideal for pumping aggressive liquids, various corrosive mixtures, solvent, wastewater with chemical impurities. The concentration of suspended solids should be no more than 1.25 mg/cubic cm. All pump components in contact with the medium are free of metal parts. Thus, no oxidation of the medium occurs in these pumps. The pumps are used even for media where contact with the atmosphere is not permitted.

 

Flow Range: to 47.9 m3/h
Viscosity: to 50 сP
Temperature: РР: +82 °С / PVDF: +104 °С
Pressure: to 6.2 bar
Materials: PP, PVDF
Internal eccentric gear pump

Internal eccentric gear pump

VALISI internal gear pumps of the VD series are positive displacement pumps with a robust and simple design (only two moving parts). This type of design allows for efficient pumping of both liquid and clean media, as well as highly viscous abrasive media with inclusions (e.g. asphalt, chocolate, honey, etc.). The pumps can pump liquids with a viscosity of 100 ~ 1.000.000 cst. The pumps provide a uniform flow and high pressure. The following gear pump designs are available: without axial support, with axial support, in-line design, monoblock design, and high-speed design.

Flow Range: max 250 m3/h
Viscosity: max 1.000.000 cst
Temperature: -40 ~ 300 ºC
Pressure: max 15 Bar
Materials: Pig Cast Iron, Spheroidal Cast ıron, Cast Steel, AISI 304/316 CrNi Stainless Steel
General industrial gear pumps

General industrial gear pumps

General purpose pumps are widely used in all areas of industrial production around the world due to their gentle handling of the fluid during pumping, as well as their simple and robust design and minimal maintenance. Thanks to the standard connection dimensions, the pumps can be combined with any motor and other drive elements that comply with NEMA or IEC standards.

Flow Range: 102 m3/h
Viscosity: 440 000 cSt
Temperature: -50 +230 °C
Pressure: 17 bar
Materials: cast iron, stainless steel
Heavy-duty gear pumps

Heavy-duty gear pumps

Heavy-duty gear pumps solve the toughest applications and ensure maximum flow rates when emptying large tanks. The foot-mounted design of the pump allows the use of various types of mechanical seals without changing the design of the pump itself (Universal Seal series). A large bearing cup located at the rear of the pump allows the installation of any seal, from a conventional stuffing box to a double mechanical seal.

Flow Range: to 364 m³/h
Viscosity: to 440,000 cSt
Temperature: -85°C to +430°C
Pressure: 14 bar
Materials: cast iron, steel, stainless steel, Alloy C, Alloy 20 and Others, Hard Materials and Coatings
Valisi lobe pumps

Valisi lobe pumps

Rotary Lobe Pumps are reliable and efficient solutions for pumping liquids in a wide range of industries that require reliable and wear-resistant technology.

Rotary Lobe Pumps are reliable thanks to its hygiene design, capable of pumping without damaging liquid’s structure, and depending on liquid’s viscosity, Rotary Lobe Pumps have the ability of generating pressure up to 12 Bar.

Flow Range: 400 m³/h
Viscosity: 250.000 SSU
Temperature: 150 ºC
Pressure: 10 Bar
Materials: cast iron
Titano series

Titano series

The pumps of the TITANO series are designed and manufactured according to API 674 and ASME standards and cover the range of medium power up to 600 kW.
These pumps are studied to guarantee a highly reliable service and to minimize the maintenance operations and the operating costs.
The TITANO series consists of 5 pump sizes in triplex execution. The 31.40 model is manufactured also in quintuplex (model 31.40/Q) and septuplex (model 31.40/S) execution, where the same components of the triplex model are used.

Flow Range: Hydraulic power: up to 431 kW
Length: Stroke: up to 150 mm

Lifting Pumps

Lifting Pumps

Lifting pumps are key components in a wide range of industrial and commercial applications that require the efficient transfer of liquids or gases from a lower level to a higher level. They play an important role in various industries such as construction, oil and gas, water supply, agriculture, as well as shipbuilding and many other areas. Lift pumps are available in a variety of configurations and sizes to meet a variety of needs and operating conditions.

Advantages of Industrial Lift Pumps

Industrial lift pumps provide reliable and efficient operation in the most demanding operating conditions. They have a number of advantages, including:

  • High performance: Industrial lifting pumps are capable of delivering a significant volume of pumped liquids or gases with minimal energy consumption.
  • Strength and durability: Made from high-quality materials, these pumps have excellent strength and durability, which ensures their long service life even under intensive use.
  • Adaptability: Industrial lifting pumps can be adapted to various operating conditions, including high and low temperatures, aggressive environments and high pressures.
  • Easy maintenance: Many lifting pump models have a design that facilitates maintenance and servicing, which reduces their operating costs.

Industrial lifting pumpsChoosing a Lift Pump

When choosing a lift pump, there are a number of factors to consider, including the type of fluid being pumped, the volume and pressure required, operating conditions, and more. It is important to choose the pump that best meets your project specifications and provides efficient and safe operation throughout its service life.

Regardless of your needs, there is a wide range of lift pumps on the market that are ready to solve the most difficult pumping tasks. With the right pump selection and installation, you can ensure the efficient operation of your production, increase productivity, and reduce overall operating costs.

Search

To search for the required pump, select from 1 to 5 parameters

All 41 options
All 54 options
All 88 options
All 50 options
All 29 options

IF YOU DON'T FIND THE RIGHT OPTION, DON'T HESITATE TO CALL US.
WE WILL HELP YOU TO FIND THE RIGHT EQUIPMENT.

quick search Download catalogue Price request
QUICK PRICE CALCULATION FOR INDUSTRIAL EQUIPMENT IN 2 STEPS
STEP 1 of 2 – ENTER THE DATA IN THE FORM BELOW:

Select a category:

Additional information:


STEP 2 of 2 – Specify the period of time during which you want to receive an accurate estimate for your request:

×
To top